View T0806_162490.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Features
* * * * * * * * * * * * *
Current-controlled Output Current Source, 3 Input Channels Two Selectable Outputs for Grounded Laser Diodes Output Current per Channel up to 250 mA Total Output Current to 300 mA (Minimum) Rise Time 1.0 ns, Fall Time 1.1 ns On-chip RF Oscillator Control of 2 Different Swings by Use of 2 external Resistors Oscillator Frequency Range from 200 MHz to 600 MHz Oscillator Swing to 100 mA Single 5 V Power Supply Common Enable/Disable Input TTL/CMOS Control Signals Small PB-free QFN16 (4 mm x 4 mm) or SSO16 Package
Applications
* DVD-ROM with CD-RW Capability (Combo Drives) * Combo Drives with CD and DVD Writing Capability
3-Channel Laser Driver with RF Oscillator and 2 Outputs T0806 (Summary)
Description
The T0806 is a laser diode driver for the operation of two different grounded laser diodes for DVD-RAM (650 nm) and CD-RW (780 nm) drives. It includes three channels for three different optical power levels which are controlled by a separate IC. The read channel generates a continuous output level whereas channels 2 and 3 are provided as write channels with very fast switching speeds. Write current pulses are enabled when a low signal is applied to the NE pins. All channels are summed together and switched to one of the two outputs IOUTA or IOUTB by the select input SELA. Each channel can contribute up to 250 mA to the total output current of up to 300 mA. A total gain of 100 is provided between each reference current input and the selected output. Although the reference inputs are current inputs, voltage control is possible by using external resistors. An on-chip RF oscillator is provided to reduce laser mode hopping noise during read mode. Swing can be set independently for the two selectable outputs with two different resistors. Oscillation is enabled by a high signal at the ENOSC pin. Complete output current and oscillator switch-off is achieved by a `low' signal at the ENABLE input. Figure 1. Block Diagram
I3 NE3 I2 NE2 IR ENABLE Channel 3 IOUTA IOUTB Channel 2
Read channel
ENOSC
RF oscillator
RF
RSA RSB
SELA
Rev. 4522DS-DVD-07/03
1
Pin Configuration
Figure 2. Pinning SSO16
IR I2 I3 RF NE2 NE3 ENABLE ENOSC 1 2 3 4 16 15 14 13
VCC1 IOUTA GND RSA RSB IOUTB SELA VCC2
T0806
5 6 7 8 12 11 10 9
Pin Description SSO16
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Symbol IR I2 I3 RF NE2 NE3 ENABLE ENOSC VCC2 SELA IOUTB RSB RSA GND IOUTA VCC1 Type analog analog analog analog digital digital digital digital supply digital analog analog analog supply analog supply Function Input current, bias voltage approximately GND Input current, bias voltage approximately GND Input current, bias voltage approximately GND External resistor to GND sets oscillator frequency of oscillator A Digital control of channel 2 (low active) Digital control of channel 3 (low active) Enables output current (high active) Enables RF oscillator (high active) +5 V power supply for IOUT High: selects IOUTA, RSA Low: selects IOUTB, RSB Output current source B for laser diode External resistor to GND sets swing of oscillator B External resistor to GND sets swing of oscillator A Ground Output current source A for laser diode +5 V power supply for IOUT and circuit
2
T0806
4522DS-DVD-07/03
T0806
Figure 3. Pinning QFN16
I3 RF NE2 NE3
1 2 3 4
16 15 14 13 12 11 10 9 5678 ENABLE ENOSC VCC2 SELA
I2 IR VCC1 IOUTA GND RSA RSB IOUTB
Pin Description QFN16
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Paddle Symbol I3 RF NE2 NE3 ENABLE ENOSC VCC2 SELA IOUTB RSB RSA GND IOUTA VCC1 IR I2 GND Type analog analog digital digital digital digital supply digital analog analog analog supply analog supply analog analog supply Function Input current, bias voltage approximately GND External resistor to GND sets oscillator frequency Digital control of channel 2 (low active) Digital control of channel 3 (low active) Enables output current (high active) Enables RF oscillator (high active) +5 V power supply for IOUT High: selects IOUTA, RSA Low: selects IOUTB, RSB Output current source B for laser diode External resistor to GND sets swing of oscillator B External resistor to GND sets swing of oscillator A Ground Output current source A for laser diode +5 V power supply for IOUT and circuit Input current, bias voltage approximately GND Input current, bias voltage approximately GND Ground
3
4522DS-DVD-07/03
Absolute Maximum Ratings
Parameters Supply voltage Input voltage at IR, I2, I3 Input voltage at NE2, NE3, ENOSC Output voltage Total output current Output current per channel Power dissipation Junction temperature Storage temperature range Notes: 1. RthJA 115 K/W, Tamb = 70C 2. RthJA 115 K/W, Tamb = 25C Symbol VCC VIN1 VIN2 VOUT IOUT IOUT (IR, I2, I3) PMAX TJ TStg 0.7 Value -0.5 to +6.0 -0.5 to +1.0 -0.5 to VCC +0.5 -0.5 to VCC -1 350 300
(1)
Unit V V V V mA mA
(2)
to 1
W C C
150 -65 to +125
Thermal Resistance
Parameters Junction ambient Symbol RthJA Value 135 Unit K/W
Recommended Operating Conditions
Parameters Supply voltage range Input current External resistor to GND to set oscillator frequency External resistor to GND to set oscillator swing Operating temperature range Symbol VCC IIR/II2/II3 RF RSA, RSB Tamb Value 4.5 to 5.5 < 3.0 >3 >1 0 to +70 Unit V mA kW kW C
Ordering Information
Extended Type Number T0806-TCQ T0806M-TCQ T0806-PEQ Package SSO16 Pb-free SSO16 Pb-free QFN16 (4 mm x 4 mm) Remarks Taped and reeled Taped and reeled Taped and reeled
4
T0806
4522DS-DVD-07/03
T0806
Package Information
5
4522DS-DVD-07/03
6
T0806
4522DS-DVD-07/03
Atmel Headquarters
Corporate Headquarters
2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314
RF/Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany TEL (49) 71-31-67-0 FAX (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland TEL (41) 26-426-5555 FAX (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131 TEL 1(408) 441-0311 FAX 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France TEL (33) 2-40-18-18-18 FAX (33) 2-40-18-19-60
Biometrics/Imaging/Hi-Rel MPU/ High Speed Converters/RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France TEL (33) 4-76-58-30-00 FAX (33) 4-76-58-34-80
Asia
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimhatsui East Kowloon Hong Kong TEL (852) 2721-9778 FAX (852) 2722-1369
ASIC/ASSP/Smart Cards
Zone Industrielle 13106 Rousset Cedex, France TEL (33) 4-42-53-60-00 FAX (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TEL 1(719) 576-3300 FAX 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland TEL (44) 1355-803-000 FAX (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan TEL (81) 3-3523-3551 FAX (81) 3-3523-7581
e-mail
literature@atmel.com
Web Site
http://www.atmel.com
(c) Atmel Corporation 2003. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company's standard warranty which is detailed in Atmel's Terms and Conditions located on the Company's web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein. No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel's products are not authorized for use as critical components in life support devices or systems.
Atmel (R) is the registered trademark of Atmel. Other terms and product names may by the trademarks of others. Printed on recycled paper.
4522DS-DVD-07/03 xM

▲Up To Search▲

Price & Availability of T0806

	To Download T0806 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .